WHAB: Still Forming Woodworking Shop & Future Grow Residence
-
- MPG Ambassador
-
Karma Hippie
- Custom Title: eye the witch Melancholy
- Location: socal
- Has bestowed Karma : 33 times
- Received Karma : 28 times
- Posts: 17529
- Joined: Mon Jun 06, 2011 1:38 pm
WHAB: Still Forming Woodworking Shop & Future Grow Resid
had to cut a rough doorway wider today
three forths, so i gotta cut out a trimmer stud
and them screw back on 3forths plywood
it was an ugly and protracted business
mostly cuz the stone guys mudded the inside
will apologize profusly
but their not going to be happy
and when my co worker ran the skisaw up that trimmer the shit was flying
heh
three forths, so i gotta cut out a trimmer stud
and them screw back on 3forths plywood
it was an ugly and protracted business
mostly cuz the stone guys mudded the inside
will apologize profusly
but their not going to be happy
and when my co worker ran the skisaw up that trimmer the shit was flying
heh
"we must strive to become good ancestors" nader
https://www.myplanetganja.com/viewforum.php?f=48
FUCK jimmydorecomedy.com
https://www.myplanetganja.com/viewforum.php?f=48
FUCK jimmydorecomedy.com
- WhiteHotAfterburner
- Advanced Grower
-
Karma Hippie
- Custom Title: Turbine Powered Toker
- Location: In an F35...above you..jus sayin.
- Has bestowed Karma : 521 times
- Received Karma : 217 times
- Posts: 6770
- Joined: Thu May 21, 2009 12:02 am
WHAB: Still Forming Woodworking Shop & Future Grow Resid
Hi Ben!bentech wrote:would like to see how you snuck up on the cut you wanted
i take it the clamps were your guides?
Yes, but I could still easily exceed the guides control and cut into the area that didn't need to be cut IF I wasn't careful.
I cut the first 2 by hand, guiding them by hand - that was taking way too long, especially since I had to bend down to do it.
I used the second one I cut to locate the cutter at the side of the cut and then placed the second clamp there - the first clamp was already holding the router table insert to the bench.
Then, I plunged in where I knew it was safe to cut into and slipped it nearer to the final cut as it fell into (onto) the clamped area.
IF I were to do it again, I'd make a circle jig for it. Super easy, super accurate, and super quick! I just wanted to get it done.
,
WHAB
ASA MPP MMJ Assist Sponsor MMJ
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
- WhiteHotAfterburner
- Advanced Grower
-
Karma Hippie
- Custom Title: Turbine Powered Toker
- Location: In an F35...above you..jus sayin.
- Has bestowed Karma : 521 times
- Received Karma : 217 times
- Posts: 6770
- Joined: Thu May 21, 2009 12:02 am
WHAB: Still Forming Woodworking Shop & Future Grow Resid
Always dirty business fixing mistakes! Especially when they're a few steps farther into the process...bentech wrote:had to cut a rough doorway wider today
three forths, so i gotta cut out a trimmer stud
and them screw back on 3forths plywood
it was an ugly and protracted business
mostly cuz the stone guys mudded the inside
will apologize profusly
but their not going to be happy
and when my co worker ran the skisaw up that trimmer the shit was flying
heh
Messin' with the other trades could wind up in fisticuffs!
Speaking of building, and I meant to mention it the other day, when I was shopping that day, I priced out 2x4x12's I need for that one tall East wall. I was going to buy a couple extras to finish up the short wall on the South, cutting them in 1/2.
12 2x4x12's were $163...
,
WHAB
ASA MPP MMJ Assist Sponsor MMJ
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
-
- MPG Ambassador
-
Karma Hippie
- Custom Title: eye the witch Melancholy
- Location: socal
- Has bestowed Karma : 33 times
- Received Karma : 28 times
- Posts: 17529
- Joined: Mon Jun 06, 2011 1:38 pm
WHAB: Still Forming Woodworking Shop & Future Grow Resid
make sure you got em lying flat and on stickers
damn i todays 2x material doesnt twist and turn just a week after purchase
damn i todays 2x material doesnt twist and turn just a week after purchase
"we must strive to become good ancestors" nader
https://www.myplanetganja.com/viewforum.php?f=48
FUCK jimmydorecomedy.com
https://www.myplanetganja.com/viewforum.php?f=48
FUCK jimmydorecomedy.com
- WhiteHotAfterburner
- Advanced Grower
-
Karma Hippie
- Custom Title: Turbine Powered Toker
- Location: In an F35...above you..jus sayin.
- Has bestowed Karma : 521 times
- Received Karma : 217 times
- Posts: 6770
- Joined: Thu May 21, 2009 12:02 am
WHAB: Still Forming Woodworking Shop & Future Grow Resid
Thanks for the heads-up, Ben!bentech wrote:make sure you got em lying flat and on stickers
damn i todays 2x material doesnt twist and turn just a week after purchase
At these prices I'm not sure how much I'll buy or get built.
I'm going to hold off on buying any for at least a little while in hopes the prices start coming down.
Although, with whose hands are on the levers of the economy currently, this 'may be' cheap in comparison....
,
WHAB
ASA MPP MMJ Assist Sponsor MMJ
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
- WhiteHotAfterburner
- Advanced Grower
-
Karma Hippie
- Custom Title: Turbine Powered Toker
- Location: In an F35...above you..jus sayin.
- Has bestowed Karma : 521 times
- Received Karma : 217 times
- Posts: 6770
- Joined: Thu May 21, 2009 12:02 am
New Arrivals...Thank You, Friend!
I had a most pleasant visit with Oldjoints yesterday!
I departed ladened with gifts
Thank you so very much, my friend!
Killer Queen(S) - 4
Mango Dream(S) -3
DJ Short Blueberry - 1
All the above - unsexed.
I also returned to a porch full of goodies!
While I don't have the netpots for them or the controller bucket yet I need to get to work on them in preparation.
And, another new arrival yesterday also included this...
The above is saving me from what I understand is a pretty ugly surgery. I was diagnosed with Cubital Tunnel several years ago. Surgery was approved. I had no desire to add to my already extensive scar collection. I suggested to the medical team a brace similar to the one above. It (they) have saved me from that surgery.
Thank you again, brother!
,
WHAB
I departed ladened with gifts
Thank you so very much, my friend!
Killer Queen(S) - 4
Mango Dream(S) -3
DJ Short Blueberry - 1
All the above - unsexed.
I also returned to a porch full of goodies!
While I don't have the netpots for them or the controller bucket yet I need to get to work on them in preparation.
And, another new arrival yesterday also included this...
The above is saving me from what I understand is a pretty ugly surgery. I was diagnosed with Cubital Tunnel several years ago. Surgery was approved. I had no desire to add to my already extensive scar collection. I suggested to the medical team a brace similar to the one above. It (they) have saved me from that surgery.
Thank you again, brother!
,
WHAB
ASA MPP MMJ Assist Sponsor MMJ
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
WHAB: Still Forming Woodworking Shop & Future Grow Residence
.
Last edited by Oldjoints on Tue Apr 27, 2021 5:51 am, edited 1 time in total.
- WhiteHotAfterburner
- Advanced Grower
-
Karma Hippie
- Custom Title: Turbine Powered Toker
- Location: In an F35...above you..jus sayin.
- Has bestowed Karma : 521 times
- Received Karma : 217 times
- Posts: 6770
- Joined: Thu May 21, 2009 12:02 am
WHAB: Still Forming Woodworking Shop & Future Grow Residence
Thank you, brother! I am looking forward to what they potentially produce! Here's one for the Girls!Oldjoints wrote:Enjoy your OD ......
Those strains should work well for that endeavor.....
Hey, that DJ Short Blueberry is also unsexed, right? I know it was a late inclusion and I don't think it was described at the same time as the others were?
All the very best to you, my friend!
,
WHAB
ASA MPP MMJ Assist Sponsor MMJ
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
WHAB: Still Forming Woodworking Shop & Future Grow Residence
.
Last edited by Oldjoints on Tue Apr 27, 2021 5:50 am, edited 1 time in total.
- WhiteHotAfterburner
- Advanced Grower
-
Karma Hippie
- Custom Title: Turbine Powered Toker
- Location: In an F35...above you..jus sayin.
- Has bestowed Karma : 521 times
- Received Karma : 217 times
- Posts: 6770
- Joined: Thu May 21, 2009 12:02 am
WHAB: Still Forming Woodworking Shop & Future Grow Residence
Thank you, sir!Oldjoints wrote:I am not positive which plant I took that clone from. I am pretty sure that DJ plant is female but not positive as I have about 10 of those in the cloner right now and that was from the last cloner run.
If I were you I would get all the KQ and MD into 3 gallon potters and the DJ into a 1 gallon ASAP.....
I planned to buy some planters last night but I rolled through town just a little bit too late. I'm going to town in a few minutes....
IF that DJ Short Blueberry is female that will make getting a Mother area started even more important! I'd like to have a mother of that Indica dominant strain!
Just the thought of a 12 bucket DJ Short grow sounds amazing! Maybe even some outdoors! *may be a dream*
Thanks!
,
WHAB
ASA MPP MMJ Assist Sponsor MMJ
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm
Federalist Papers >>> http://www.foundingfathers.info/federal ... dindex.htm